Free Plumbing Apprenticeship Phase 2 Practice Test 2026
200 Phase 2 plumbing questions and four 50-question practice tests. Free to start, no account needed.
Try one now
Pick an answer
After cutting copper with a wheel cutter, the inside edge is:
The Plumbing Phase 2 exam at a glance
Phase 2 of the SOLAS National Plumbing Apprenticeship is the first off-the-job phase: 21 weeks in an Education and Training Board (ETB) training centre. It has four modules: Thermal Processes and Mild Steel Pipework, Domestic Hot and Cold Water Services, Central Heating, and Communications and Team Leadership. Apprentices are assessed by theory exams, practical assessments and skills demonstrations, set centrally by SOLAS, marked out of 100 by the training centre and graded fail, pass, merit or distinction. The SOLAS pass grade is 50%; an apprentice who falls short is referred and may sit again. SOLAS does not publish the number of questions or the time for each theory paper. The whole apprenticeship takes at least four years and leads to a Level 6 Advanced Certificate Craft - Plumbing.
Tigertest has 200 Plumbing Phase 2 practice questions with explanations, free to start with no account required.
- Run by
- SOLAS, delivered in ETB training centres
- Phase 2 length
- 21 weeks off the job
- Modules
- Thermal processes and mild steel pipework; domestic hot and cold water; central heating; communications and team leadership
- Assessment
- Theory exams, practical assessments and skills demonstrations
- Pass grade
- 50% (graded fail, pass, merit or distinction)
- Question count and time
- Not published by SOLAS
- Award at the end
- Level 6 Advanced Certificate Craft - Plumbing
Updated by the Tigertest team. Practice questions follow the SOLAS plumbing programme brochure and the SOLAS Craft Apprenticeship Assessment Rules (2023), checked November 2026. Exam rules change, so confirm current details with SOLAS Craft Apprenticeship Assessment Rules.
How It Works
Train by Module
Four training sets: safety and copper jointing; mild steel pipework, valves and taps; domestic hot and cold water; and central heating with communications. Questions you miss come back until you have mastered them.
50-Question Practice Tests
Four practice tests of 50 questions, marked against the SOLAS pass grade of 50%. No question appears in more than one test, and every answer comes with a short explanation.
Built on the SOLAS Phase 2 Modules
Phase 2 runs for 21 weeks in an ETB training centre and has four modules. SOLAS publishes no weights for its theory papers, so Tigertest splits each 50-question test across eight topics: 5 hot work and safety, 7 copper jointing, 7 mild steel pipework, 4 valves and taps, 7 cold water, 7 hot water, 9 central heating and 4 drawings, calculations and teamwork.

Help Make Tigertest Better
Have an idea, a topic you'd like covered, or a question that could be clearer? We read every message and use it to improve every test.
Share FeedbackHow to Pass Your Phase 2 Plumbing Theory Exams
1. Get hot work and jointing right
Hot work permits and fire watching, oxygen and gas cylinder safety, capillary and compression joints, flux, brazing, bending copper, and threading, measuring and bending mild steel tube.
2. Learn the Irish water rules
TGD G: the kitchen sink on the service pipe, cistern sizes of 212 and 340 litres, the stopcock near the entry point, 6 litre WCs. TGD H: trap sizes and seals and branch connections.
3. Know hot water and heating controls
Vented and unvented cylinders and their safety devices, boiler interlock, zoning over 100 m², programmers, cylinder thermostats and zone valves, inhibitors, condensate pipes and carbon monoxide alarms.
4. Practise the calculations
Scales, cistern volumes and weights, pressure from head of water, flow and cut lengths. Then take the 50-question tests and aim well above the 50% pass grade.
Plumbing Phase 2 Frequently Asked Questions
What is Phase 2 of the plumbing apprenticeship?
The SOLAS National Plumbing Apprenticeship has seven phases over at least four years. Phase 2 is the first off-the-job phase: 21 weeks in an Education and Training Board training centre, covering four modules: Thermal Processes and Mild Steel Pipework, Domestic Hot and Cold Water Services, Central Heating, and Communications and Team Leadership.
How is Phase 2 assessed, and what is the pass mark?
Apprentices are assessed by theory exams, practical assessments and skills demonstrations, and must pass every phase exam. SOLAS sets the papers and marking schemes centrally and the training centre marks them out of 100. The SOLAS pass grade is 50%, and results are graded fail, pass, merit or distinction. An apprentice who falls short is referred and can sit again.
How many questions are on the Phase 2 theory exams?
SOLAS does not publish the number of questions or the time for each theory paper. Tigertest's practice tests have 50 questions each, spread across the four Phase 2 modules, and use 50% as the pass line with a higher score as your target.
Are the questions based on Irish rules?
Yes. Water and drainage questions follow Technical Guidance Documents G and H, heating and hot water questions follow TGD J, TGD L and the Department of Housing and SEAI heating guide, safety questions follow HSA guidance and the Safety, Health and Welfare at Work Act 2005. UK rules are not used.
Are these the real SOLAS exam questions?
No. Every question is original, written by Tigertest from the official sources. Tigertest is not affiliated with SOLAS or any Education and Training Board, and no exam paper, sample assessment or course workbook question was used.
I teach a Phase 2 plumbing course at an ETB training centre. Can my students use Tigertest?
Yes, for free. Make a class at tigertest.io/teach, post one link, and students join with just their name. You see who practiced, their test scores and the topics your class misses most.
Plumbing Phase 2 sample questions and answers
6 of the 200 practice questions, one from each topic, with the answer explained.
1. A branch pipe must not join a stack lower than what height above the bend at its foot in a house of up to three storeys?
- A.750 mm
- B.450 mm
- C.150 mm
- D.300 mm
Answer: B. TGD H paragraph 1.2.2.4: not lower than 450 mm above the invert of the tail of the bend at the foot of the stack.
2. A plumber and apprentice share a job. Who agrees the order of work with the electrician?
- A.The electrician's apprentice
- B.The client, on the day
- C.The apprentice, being first on site
- D.Whoever runs the job
Answer: D. Coordination with other trades is the responsibility of whoever is in charge of the job, so sequences such as first fix are agreed once.
3. What tool opens the end of one copper tube so another slides inside it?
- A.Tube expander
- B.Tube cutter
- C.Deburring tool
- D.Bending spring
Answer: A. An expander enlarges the tube end into a socket so two tubes can be soldered or brazed without a separate fitting.
4. Each hot water circuit in a dwelling should have:
- A.Its own separate boiler
- B.Its own gravity primary
- C.Its own temperature control
- D.One shared thermostat
Answer: C. The guide: where more than one hot water circuit exists, each should have separate temperature controls.
5. On a two-pipe radiator system, the lockshield valve is used to:
- A.Vent air from the top
- B.Fill the system from the main
- C.Balance flow through the radiator
- D.Turn the radiator on and off daily
Answer: C. The lockshield is set once during balancing so each radiator gets its share of flow. The other valve is the user's control.
6. Before digging a trench for a water service, which HSA code should be followed?
- A.Avoiding Danger From Underground Services
- B.Code of Practice for Working in Confined Spaces
- C.Code of Practice for Fire Safety of Furnishings
- D.Guide to Part 8: Explosive Atmospheres
Answer: A. The HSA points to its Code of Practice for Avoiding Danger From Underground Services, and to Dial Before You Dig, before excavation near buried gas and electric cables.
Related practice tests
Every test on Tigertest is free to start, with no account needed.
- Safe Pass Practice TestSOLAS · Safe Pass construction safety awareness programme
- SPSV Entry Test PracticeNTA (Ireland) · SPSV Driver Entry Test, Industry Knowledge module
- QFA Regulation Practice TestCentral Bank of Ireland Minimum Competency Code · QFA Regulation module (LIA)
- PSA Security Guard Practice TestQQI 4N20604 · Private Security Authority security guard (guarding) licence
- HCAP Practice TestDeer Alliance · Hunter Competence Assessment Programme (HCAP), approved by NPWS
Ready for Your Phase 2 Theory Exams?
Start for free. No account required. 200 questions on pipework, water services, heating and safety.
Start practicing